437 Welcome to your Saudi Aramco Work Permit Receiver Exam Name Email 1. The receiver must stop work if_____________. The issuer leaves the job site the designated representative must leave The work site becomes un safe. He can not find the issuer. None 2. Work permit authorize ……….. Specific tools at general location General equipment at all work site General work at specific plant Specific work at specific location None 3. What should be a assigned when working near combustible materials? Standby man Fire men Flag man Fire watch None 4. Who is responsible for the safety on the work site? The issuer The receiver Both issuer and receiver Both fire watch and the standby man None 5. Why is the check list section important to issuer and receiver? It defines the duration and scope of work. It makes sure important steps have been taken. It tells them all precautions to take. It controls the receiver’s break time. None 6. What is oxygen deficiency? Less than 23.5% oxygen Oxygen that above it’s flash point Higher than normal amount of oxygen A lower than normal amount of oxygen None 7. What happens if work must continue past the time the original permit was to expire? Stop work and come back the next day. Keep working, but tell the issuer. Work can continue until the job is completed. Extend the permit or issue a new one. None 8. What responsibility do issuers and receivers share when signing a work permit? Monitoring the operation of process Getting countersignatures from superintendent Responding to emergency events Maintaining safety conditions at the site None 9. Restricted areas include which locations? Dining halls, housing units, and operating area Pump stations, tank farms, and gas well Welding shops pump stations, and assembly area Gas plants, tank farms, and assembly areas None 10. “use a fire blanket” or “hand dig only” are example of what? precautionary hazards Additional precaution Hazards Regular precaution None 11. Which work permit requires sewer to be covered within 75 feet? Hot Cold Entry Release None 12. What is the acceptable level of LEL to allow hot work 10 to 100 PPM 0.0 PPM 5% to 50% 21% 23.5% None 13. What are the basic precautions for cold work? Select all items that apply. Fire watch Special work precautions PPE & Barricade and warning signs Gas test Standby man None 14. The use of a vehicle in an operating area requires, which work permit? Release Cold Hot Entry None 15. Who should keep the work permit? The receiver The standby man The fire watch The issuer None 16. What is the purpose of the work permit system? To authorize specific construction or maintenance work. what do you call an area where work permits are required? To insure that the hot work is not done in restricted area. To document where receiver start work for time keeping. None 17. We use work permits in hazardous areas to identify——– Alternated representative Hazards and precautions Expired permit The designated representative None 18. What are the basic precautions for hot work permit? Select all items that apply? Fire watch Blind, isolate, clean, and purge equipment Fire protection equipment All of the Above Gas test Cover sewer drains None 19. work permit can be issued for up to 30 days if_______________ It is highly unlikely that conditions will change The work site is far away Only cold work will be done The receiver can not close the work permit None 20. Who must sign the work permit to close it? Gas tester, issuer and receiver Competent person Issuer and receiver Designated representative None 21. What training should a fire watch have? Operate heavy equipment Operate radio equipment Operate fire equipment Operate control room None 22. what do you call an area where work permits are required? Dangerous area. Controlled area. Sensitive area. Restricted area. None 23. Who must sign a work permit to extend it? The new issuer, receiver, and gas tester The new issuer and receiver Superintendent’s countersignature is required The new area foreman and the new issuer None 24. Who should point out all hazards and write on the work permit? The standby man The issuer The receiver The fire watch None 25. Why must equipment be de-energized and depressurized before work is started? Accidental start-up could happen Purge gas can be lost Locks and tags will deteriorate Gas tests are not accurate None 26. What must the issuer do if a joint site inspection is not done? Write why not on the work permit Tell his foreman Required barricades and warning sign A sign a designated representative None 27. The issuer must try to start –up equipment at the field switch after it has been isolated and before work starts to make sure: There is no tag in the area Locks and tags are installed The receiver’s tag is installed It can not accidently start None 28. Who install locks and tags first? electrical engineer Sceco Operations Power distribution None 29. Who is a work permit receiver? A person certified to receive permits A person nominated by his supervisor A qualified Saudi Aramco employee A maintenance or contract worker None 30. What are the basic precautions for confined space entry, select all items that apply. Isolate, clean, and purge equipment Install lighting A sign a standby man Install air mover Take gas tests All of Above None 31. What hazard would you find when doing hot work? Auto ignition temperature Ignition switch Ignition source Ignition point None 32. Which of the following is NOT a restricted area? Dump site. Tank farm. Gasoline station. Loading pier. None 33. A release of hazardous liquids or gases permit is required when? Operations drain equipment Operators release hydrocarbons to the flare Pipefitters open a line or install blinds Crafts man builds a scaffold None 34. Any worker can be a sign as standby man? True False None 35. (1) The issuer must stop work if ————-? (2) A pipe fitter can not work on the same pieces of equipment using welder’s permit because. Welders are usually contractors. Each type of work involves different hazards. Gas tests are not needed for pipefitters. Joint site inspections are not needed for pipefitters. None 36. What considered cold work? Sand removal and scaffold building Scaffold building and grinding Brush painting and abrasive blasting Abrasive blasting and painting None 37. What must the issuer write on the work permit? Badge number and certificate expiry date. Name, organization code and badge number Gas test results, name and badge number Name, badge number, and certificate expiry date None 38. Where must the receiver keep work permit after it is issued? Display at the job site or in his possession Within the 75 meter of the work permit With senior crew member In the control room None 39. Who decides whether an area should be restricted or not? The department manager The superintendent The issuer The receiver None 40. Where could an issuer find out which permit to issue for a special job? Facility operating instructions On the front of any work permit Corporate loss prevention manual On the back of any work permit None 41. What must the receiver do if he stops work? Tell his immediate supervisor Tell the issuer Tell the designated representative Tell the senior crafts man None 42. if a work permit is not issued during an emergency, what must be done to do the work? Wear Scott air Pak. Superintendent must approve. Joint site inspection. All safety precautions must be taken. None 43. The information’s entered in the “exact work location” box is important Because it controls? How many workers can be at the job site Where the receiver can work What equipment the receiver can use How long the receiver can work None 44. who is responsible for safety at the work site after a permit has been extended? The one who originally did the joint site inspection. The issuer and receiver who signed the extension. The original issuer and receiver. The person who countersigned the permit. None 45. The safety of work site is a sole responsibility of an issuer? False True None 46. Who should ask for work permit before they start working? The standby man The receiver The issuer The fire watch None 47. The receiver can leave the job site any time as long as he gets the Permeation from his supervisor. True False None 48. What information must the gas tester enter on the work permit? Gas test results and normal level LTX-310 expiry date, name and badge number Gas test results, name and badge number Badge and certificate number None 49. What considered cold work? Abrasive blasting and painting Scaffold building and grinding Sand removal and scaffold building Brush painting and abrasive blasting None 50. Who can decided that work is a low risk and that a work permit is not needed? The receiver The department manager The superintendent The issuer None 51. what type of work does the work permit system authorize? Specific construction, maintenance, or repair work All work done by maintenance or contractors Non- hazardous work where safety is important All work constructed for Saudi Aramco None 1 out of 6 Please fill in the comment box below. Share 0 FacebookTwitterPinterestLinkedinRedditWhatsappTelegramEmail previous post Work Permit Receiver next post Saudi Aramco Permit Receiver Latest Questions and Answers
